C-STN20 SPI PERFORMANCE KIT and C-STN20BUDGET KITSINGLE POINT 1992-1996

This kit has been specifically designed to work with the factory fitted existing single point engine management system. No modifications are necessary

Please beware that if prolonged speeds of 100mph are envisaged the engine may run lean and could eventually lead to engine failure. Power output figures of around 80bhp are normally expected after fitment but is dependant on the original engine build (rolling road tests have consistently shown 20-25% increases).

Figures confirmed by Swiftune Racing. Extra BHP can be obtained with professional air box modification. Further power increases would necessitate modifications to inlet manifold and use of a tubular steel LCB exhaust manifold. These performance figures apply equally to both kits and the only difference is the material of the valves and the different type of 1.5 rockers used. The budget kit uses forged rockers and includes 4 extra washers to shim correct alignment over the valve stems. Fit 2 of AEG168 washers b...

SUSPENSION - Terminology

Glossary of terms used in the suspension on the mini. The Mini has consistently more than proven its capability in competition with very limited and cost-effective modifications based on the standard equipment fitted. Having first ensured the bodyshell (in reality little more than a complex bracket to hold suspension and driver securely in place) is well sorted out by removing all cruddy or rotten metalwork and into something like straight, square and strong we, maximising suspension stability and geometry pays dividends in the enjoyment that is driving a Mini. Understanding what the individual ingredients are helps in pursuing what you want from the experience. Smooth Mover Good, reliable, and consistent handling is dependent on a number of factors. At this stage, we’re concerned with clapped out or badly adjusted suspension components. Stiff, seized, partially seized or slack, sloppy, worn out suspension components will cause inconsistent, wayward, confusing and – more important

Gearbox - Up-rating diffs and FDs

There’s a good selection of straight-cut final FDs available. Examine the FD table, and using information from

'Gearbox - Final dives, standard' and 'Gearbox - Formulae for car speed, etc.'

you can assess which would best suit your usage. Bear in mind that they’re noisy, make sure you select one that’ll fit your diff unit, and also consider that using drop gears will allow fine-tuning of the ratio where necessary. See

'Gearbox - Up-rating drop gears'

Gearbox - Up-rating diffs, FDs and ancillaries.

part numbers: C-BTA166, C-BTA167, DAM6624, BTA101, 2A7062, DAM5071, DAM6027, RPS1418, C-AJJ3385, C-22A1731, ...Read more

GEARBOX - Syncro vs 'Dog' engagement

NOTE

; A 'high' or 'low' ratio gear is in reference to it's performance, not it's numerical number. To illustrate - a 'high' FD ratio will give 'higher road speed', but will have a numerically low figure. A 'low' FD ratio will give lower road speed, but have a numerically high figure. part numbers: C-AJJ3371, C-AJJ3319, C-STN39, C-AJJ4014, C-STN76, C-STN77 A by-product of this will be reduced acceleration capability on the 'high' ratio, increased acceleration capability on the 'low' ratio. The main gearbox gears work in the exact same way. Cog swapping Elsewhere we've considered what alternative standard production ratios are available - but that still leaves you with the power-consuming and limited-ratio alternatives helical tooth type gears. Not desirable in a competition orientated car. The solution to this comes in the form of several types of straight-cut gear sets (teeth are cut at 90 degrees across the gear as opposed to the angled helical type).

Brakes - Fundamental Considerations

When looking to increase their cars performance, most folks immediately turn to considering higher engine power outputs. Because of this pre-occupation brakes tend to slide down the improvements priority list. However, they are far more important - being able to accelerate at warp speed to hyper-space in the twinkling of an eye is all very well, but disastrous if you can’t stop. You will make a very big hole in the scenery, and possibly end up wearing an wooden over-coat. Getting the braking system sorted out can help to make the car quicker, as you will be able to more confidently, therefore maximising speed in any given situation. Being one of those ‘sciences’ used in the automotive industry I hope to shed some light on the subject as it's another of those where many questions from confused and mislead folks that clog up my e-mail board. The advent of the Metro, and the brakes used on it has spawned a lot of activity in this direction. It was soon discovered that they could b

Rocker gear - General compendium

Whether you’re building a solid road performer or fire-breathing monster, the main goal is to improve air/fuel flow into the engine. The more you can get in, the more power you can get out. Cheapest chunk of power improvement comes from sorting the asthmatic manifolding and exhaust by applying a stage one kit. Then what? Considering the ‘get more in to get more out’ theme, the main restriction - all else being equal - is the valves and their behavior. How big they are, how efficient they are and how long they’re open for determines how much gets in with each gulp each bore/piston makes. Modified cylinder heads are popularly next, although it has to be said that although a well modified cylinder head will improve performance, the gain against cost is nowhere near that given by the ‘stage one’ kit application. A good stage one kit’s improvement verses cost is around £12.50 per 1 hp, a decent modified head typically £30 per 1hp - dependent on application. Hmm.

Distributor - Electronic Ignition

Since the A-Series has such an efficient combustion chamber design, the standard points set-up is perfectly capable of providing sufficient sparks for effective combustion when new. And this is the problem. They require regular servicing to maintain maximum performance. This can be a chore, so is generally neglected. And it doesn't take long before deterioration seriously affects performance. Points bounce is also a problem on high-revving race motors.

Deterioration of the points set-up can be caused by several factors - wear and tear on the dizzy spindle bearings creating 'wobble', electrical erosion of the points, and wear of the points cam heal. All have the same effect - dwell angle alteration. This in turn reduces spark effectiveness. The consequences are a loss in power and economy, poor starting performance, and general poor running.

Engine - 1098, Initial Tuning

The 1098 (1100) engine has had a lot of bad press over the years - largely because of early experiences when trying to tune the motor brought about problems with the then standard components available - they simply were not up to taking any real punishment as experienced in racing.

See bottom for useful part numbers.

This fallacy was handed down generation to generation like some scary bedtime story. Those that have used the unit in more recent years, employing more capable componentry know what a demon motor this can be. Following is an initial look at what it will do with a little modification - the results compared directly with it's smaller brother the 998 for illustration of the potential.

Abridged History
When the Mini was first conceived it ustilised a de-stroked version of the then quite remarkable 948cc A-series engine.

Engine - 998 Tuning, Bolt-ons

The 998cc engine is a very robust and tunable unit. It is also the most common engine found in standard Minis. See bottom for useful part numbers Terminology: MSC/MM - Mini Spares Centre/Mini Mania ID - Inside Diameter OD - Outside Diameter BBU - Big Bore Unit (refers to all 1275cc-based units) SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998) BHP - Brake Horse Power LCB - Long Centre Branch Despite the lure of the much-advertised 1380cc alternatives, many simply want to get a little more from what they have at reasonable outlay. The single biggest restriction on any standard Mini is the 'breathing apparatus' - anything that is connected to the induction and exhaust systems. The standard exhaust being the biggest culprit - it is desperately restrictive in the name of noise suppression and cheapness of manufacture. Oddly enough it also increases fuel consumption when tested over a better designed, fre

Flywheel - Pre-Verto Types

The early spring-type clutch flywheels are of no use except where total originality is required on a concours car. The taper is too small and diaphragm pressure ring non-existent. No use to man nor beast. Part No Applications: C-AEG421, C-AEG420, C-AEG619, C-AEG620, 2A3657, 2A3658, 2A3659, 2A3512 With the exception of the fact the two-piece flywheel is two pieces bolted together - this and the later one-piece cast item can be treated as the same thing. They will universally fit all transverse engine cranks from 1964 onwards, so that should be easy enough. If all you can get is the hulking great 1300 type, then this too is as universal to fit, but I highly recommend you get that extra cast lump machined off of the outer edge as a bare minimum. Further lightening of these cast flywheels is possible by having metal machined off of the diaphragm side, from the outer edge of the diaphragm pressure ring outwards.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

Winter is coming.........

Cold running and why tuned Minis simply quit running when pulling up.

Winter is coming, and with it various issues that affect Minis used throughout the year, no matter what the conditions.

This month's consideration is cold running and why a plethora of tuned Minis simply quit running when pulling up. Ignoring the few that are down to various other ailments, the main issue is just the cold weather. Those that suffer more ...

SUSPENSION GEOMETRY - Buy the right parts to do the job correctly

It is baffling to see so many companies advertising mini suspension geometry parts in kits that are a waste of time as they rarely complete the job on either the front or the rear.

Bill Sollis starts the 2005 race season with new colours.

The red lights went out after a short wait and the 2005 season was underway. I held position and went early on the attack,

It seems remarkable, but a winter break of over six months is never enough time to prepare a racing car! The truth is, at long last I've completely refurbished the hall, stairs and landing at home. That concludes a 7 and a half year ...

Cylinder head - Identification by casting number

A+ head castings - despite having the same 12G940 casting number - are considerably different in appearance, loosing the flat area behind the thermostat housing and around the rest of the rocker/head stud areas to a sculptured look - where these areas are replaced by a 'sunken' cast finish. The A+ castings were introduced with the appearance of the Metro in 1980, although some late 1275GTs (1979-on) had them fitted. Generally they are easily recognised by their colour - a putrid yellow on the small-bore castings and bright red on the large-bore ones, a paint finish that is VERY difficult to remove, even in a chemical tank. The MG

See bottom for useful part numbers.

Now this may not be super-sonic speed-inducing power, it could just as well be for maximum economy. In either case, it's the engines volumetric efficiency (VE) under scrutiny - it's ability to breath in as much correctly proportioned air/fuel mix as possible in any given situation.

Cylinder head - Suitability basics

Whatever else owners do to their Minis by way of interior/exterior modifications or none at all, a very large proportion desire and search for an increase in engine performance.

See bottom for useful part numbers.

Now this may not be super-sonic speed-inducing power, it could just as well be for maximum economy. In either case, it's the engines volumetric efficiency (VE) under scrutiny - it's ability to breath in as much correctly proportioned air/fuel mix as possible in any given situation. Although the induction/exhaust system plays an important part, there are effectively two major factors that dictate performance increases - the camshaft and cylinder head. The induction and exhaust elements (stage one kits, exhaust systems, etc.) and camshafts are covered in various other articles in my 'Corner'. So here we'll have a look at cylinder heads and dispel some of the myths and legends surrounding them.

Engine - 998 tuning, bolt-ons (stage one)

The 998cc engine is a very robust and tunable unit. It is also the most common engine found in standard Minis. Despite the lure of the much-advertised 1380cc alternatives, many simply want to get a little more from what they have at reasonable outlay.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money.

Engine - 998 tuning, further options

Following on from the easily bolted on performance enhancing components out-lined in the stage one section, we need to consider where to go to get more power output.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money. Power production of any engine, once the 'breathing apparatus' (induction/exhaust system) has been dealt with to cause no restriction ...

Engine - 1275, 95bhp sports/tourer test result

DIY enthusiasts often believe that building an engine to give excellent all-round road performance is beyond them. Mainly from comparisons made between what they have been able to achieve and what specialists say should be achievable from any particular type of engine build.

Generally scrambled further by the non-perfect match of parts and components used between aforementioned specialist and erstwhile DIY-er, and the ritual 'nose-tapping and knowing winks' display of those specialists. Something you can very nearly 'see' even when talking to such folk on the phone - or that inimitable 'ah, yes, well…' So some form of 'black art' is implied. Whilst there is most definitely a degree of 'feel' involved between the real specialist's results and those of just a good engineer - the bones of the deal is subject to no such thing and is certainly within the capability of the DIY enthusiast given the necessary information. And that has been the problem.